Details
Tanks inc. Universal EFI Gas Tank Kit w/ 0-90 Ohm Sender & 400LPH Pump - UT-N-2HT-KITGML6
KIT CONTENTS:
UT-N-2HT: Universal Pickup Truck Fuel Tank with Fuel Injection Tray
GPA-6: High Performance Fuel Pump Module - 400 Liters Per Hour
TAN-GML: 5 Bolt Fuel Sending Unit - 0-90 Ohm
------------------------------------------------------------------------------------------------
UT-N-2HT: Universal Pickup Truck Fuel Tank with Fuel Injection Tray
Universal Pickup Truck Fuel Tanks
- Alloy Coated Steel
- 16 Gallon Capacity
- Vent Required for Fuel Injected Engines
- Includes Universal Mounting Straps
- Includes Internal Reservoir Tray for Fuel Injection
- Fully Baffled
- Size: 27-3/4" x 17-3/4" x 8-1/2"
- Accepts All Popular 5-hole Senders If using tube sender length is 7"
GPA-6: High Performance Fuel Pump Module - 400 Liters Per Hour
Turbine Style High Flow GPA Series Fuel Pumps
- Made in the USA
- Heavy 10 gauge no-warp mounting plate
- 1/4" NPT Supply and Return Line
- Barbed Vent Fitting
- Oven brazed fittings
- Up to 100 PSI
- In-tank wire harness
- Genuine Walbro High Flow High Horsepower Fuel Pumps
- Powerful & Quiet Operating DCSS 39/50 Turbine Pumps
- Pumps can be controlled by Pulse Width Modulation
The GPA-Series Fuel Pump Module is designed to be used in many of our die-stamped alloy-coated and stainless steel gas tanks that have factory-installed reservoir trays. The tray is an absolute necessity for fuel-injection in order to prevent fuel starvation when accelerating and cornering.
We use Walbro high-performance pumps in all of our fuel injection modules. Walbro (TI Automotive) is an OE validated pump manufacturer that supplies products for two-thirds of the vehicles produced around the world today. Based on our testing we believe that Walbro offers the highest quality pump on the market. These patented design dual channel deep pocket pumps produce high flow volumes at unparalleled efficiency that is better at hot fuel handling and recovery from aeration compared to other pump manufacturers. We offer multiple flow ranges in order to supply up to 1000 horsepower. The internal wiring harness, supply line, return line, filter sock and insulator sleeve are included. (The gasket and screws with o-rings are not included with the pump because we include gaskets and screws with our tanks.)
The heavy 10-gauge no-warp mounting plate contains fittings for the supply, the return, the vent and the electrical connectors. It is yellow-zinc plated to prevent corrosion.
These pumps are not compatible with the 1968-72 GM-A Body stock sized (non-notched) EFI Gas tanks.
TAN-GML: 5 Bolt Fuel Sending Unit - 0-90 Ohm
This fuel tank sender mounts with five mounting screws. It is adjustable to work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground they work on all 6-24 volt systems positive or negative ground. They do not have a fuel pickup tube built into them as some original senders may have. Made with a high quality ceramic board rheostat. Our fuel senders are available for the following applications.
Application Listing:
- SW - SW gauges - 240-33 Ohms
- VDO - VDO gauges - 10-180 Ohms
- GME - GM up to 1964 - 0-30 Ohms
- GML - GM 1965 and up - 0-90 Ohms
- ORG - Early Ford & Mopar - 73-10 Ohms
The first number of the (Ohms) represents empty and the following is for full.