Details
Tanks Inc. 1967-72 Chevy Truck Frame Mount Tank Kit - 0-90 - TM6372-HT-KITGML
KIT CONTENTS:
TM6372-HT: 1963-72 Chevy Truck Frame Mount EFI Tank Bed Fill w/ Neck & Cap - TM6372 Filler Neck Option: 2" ID x 6" Hose Connection
GPA-4: High Flow Fuel Pump Module - 255 Liters Per Hour - Up to 630 hp / kt
TAN-GML: 5 Bolt Fuel Sending Unit - 0-90 Ohm
----------------------------------------------------------------------------------------------------
TM6372-HT: 1963-72 Chevy Truck Frame Mount EFI Tank Bed Fill w/ Neck & Cap - TM6372 Filler Neck Option: 2" ID x 6" Hose Connection
TM6372-HT: 1963-72 Chevy Truck Frame Mount EFI Tank Bed Fill w/ Neck & Cap - TM6372 Filler Neck Option: 2" ID x 6" Hose Connection
TM6372-HT: 1963-72 Chevy Truck Frame Mount EFI Tank Bed Fill w/ Neck & Cap - TM6372 Filler Neck Option: 2" ID x 6" Hose Connection
TM6372-HT: 1963-72 Chevy Truck Frame Mount EFI Tank Bed Fill w/ Neck & Cap - TM6372 Filler Neck Option: 2" ID x 6" Hose Connection
This tank mounts under the truck bed using the flanges to bolt in place. The tank is designed to bolt up to the bottom side of the frame rails but it can be mounted in different configurations including on top or even in-between the rails in some cases. It is up to the installer to drill and locate the mounting holes. Mounting hardware not included.
- 1963-72 Chevy and GMC Pickup Under Bed Frame Mount Gas Tank
- Bed Fill Filler Neck. Available with an Aluminum Cap or 2" ID Connection Hose
- Die Stamped Galvanized Steel then Powder Coated Silver
- Fuel Injection Ready!
- Utilizes our GPA series fuel pumps, available in sizes from 109 to 450 liters per hour.
- Uses aftermarket 5-bolt senders. Multiple Ohm ranges available to work with factory or aftermarket gauges. If using tube sender length is 9".
- EFI style internal baffling with extra large 4.8 liter dual tube baffled fuel tray to prevent fuel pump starvation.
- If using on a carbureted application use part# PTA-G
- Available with a 2" tall neck and aluminum cap or with a stub neck and fuel hose
- 18 Gallon Capacity
- Size is 32-1/4" x 20-1/2" x 9-3/4" (including the mounting flange)
- Size is 28" x 20-1/2" x 9-3/4" (measured without the mounting flange)
GPA-4: High Flow Fuel Pump Module - 255 Liters Per Hour - Up to 630 hp / kt
GPA-4: High Flow Fuel Pump Module - 255 Liters Per Hour - Up to 630 hp / kt
- Made in the USA
- Heavy 10 gauge no-warp mounting plate
- 1/4" NPT Supply and Return Line
- Barbed Vent Fitting
- Oven brazed fittings
- Up to 100 PSI
- In-tank wire harness
- Genuine Walbro Fuel Pumps
The GPA-Series Fuel Pump Module is designed to be used in many of our die-stamped alloy-coated and stainless steel gas tanks that have factory-installed reservoir trays. The tray is an absolute necessity for fuel-injection in order to prevent fuel starvation when accelerating and cornering.
We use Walbro high-performance pumps in all of our fuel injection modules. Walbro (TI Automotive) is an OE validated pump manufacturer that supplies products for two-thirds of the vehicles produced around the world today. Based on our testing we believe that Walbro offers the highest quality pump on the market. These OE quality performance pumps are better at hot fuel handling and are designed with an internal bypass channel to offer better recovery from aeration compared to other pump manufacturers. We offer multiple operating ranges in order to supply up to approximately 1000 horsepower. The internal wiring harness, supply line, return line, filter sock and insulator sleeve are included. (The gasket and screws with o-rings are not included with the pump because we include gaskets and screws with our tanks.)
The heavy 10-gauge no-warp mounting plate contains fittings for the supply, the return, the vent and the electrical connector. It is yellow-zinc plated to prevent corrosion.
TAN-GML: 5 Bolt Fuel Sending Unit - 0-90 Ohm
This fuel tank sender mounts with five mounting screws. It is adjustable to work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground they work on all 6-24 volt systems positive or negative ground. They do not have a fuel pickup tube built into them as some original senders may have. Made with a high quality ceramic board rheostat. Our fuel senders are available for the following applications.
Application Listing:
- SW - SW gauges - 240-33 Ohms
- VDO - VDO gauges - 10-180 Ohms
- GME - GM up to 1964 - 0-30 Ohms
- GML - GM 1965 and up - 0-90 Ohms
- ORG - Early Ford & Mopar - 73-10 Ohms
The first number of the (Ohms) represents empty and the following is for full.